Fix & Seal Power

Applications

– Bonding of all types of building materials onto all
porous and nonporous surfaces.
– Elastic bonding of objects, panel profiles and other
pieces on the common substrates.
of concrete, stone, plasterwork, wood, chipboard etc
– Strong elastic bonding in vibrating constructions.

Properties

– High initial tack
– Reduced need for support
– Very good adhesion on many materials, even if
slightly moist
– High shear strength after full cure (no primer)
– For in and outdoor use
– Permanently elastic after curing
– No odour
– Can be painted with water based systems

Packaging

Dolphin Fix and Seal power is available in cartridge (280 ml) and foiled bag (600 ml) other
package on request

Storage and shelf life

12 months in unopened packing in cool and dry storage place at temperatures between +5°C
and +25°C.

Substrates

Substrate condition:
The substrates must be rigid, clean, dry, free of dust and grease.

Substrate Preparation:
Porous surfaces in water loaded applications should be permitted with primer 150. Prepare
non-porous surfaces with a activator or cleaner. While producing plastics very often releasing
agents, processing aids and other protective agents (like protection foil) are used. These should
be removed prior to bonding or sealing. For optimum adhesion use of surface activator is
recommended.

Substrate types:
Dolphin Fix & Seal Power has a good adhesion to following substrates: all usual building
substrates, lacquered wood, AlCuMg1, AlMg3, Stainless steel, electrolytic galvanized steel, steel,
steel ST1403, hot dip galvanized steel, polycarbonate (Makrolon®), polyamide, fiberglass,
reinforced epoxy, polyester, Dolphin Fix & Seal Power has no good adhesion or is not suitable
for PE, PP, PTFE (Teflon®), bituminous substrates, copper or copper containing materials such
as bronze and brass Bonding plastics like PMMA (e.g. Plexi® glass), polycarbonate (e.g
Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing
in these substrates. The use of Dolphin Fix & Seal Power is not recommended in these
applications. We recommend a preliminary adhesion and compatibility test on every surface.

Application Method

with manual or pneumatic caulking gun
Cleaning: Clean with white spirit or surface cleaner, immediately after use
Repair: with the same material

Health and Safety Recommendations

Take the usual labour hygiene into account.
Consult label and material safety data sheet for more information.

Remarks

• Dolphin Fix & Seal Power may be overpainted with water based paints, however due to
  large number of paints and varnishes available we strongly suggest a compatibility test
  before applications.
•  Drying time of alkyd resin based paints may increase.
•  Dolphin Fix & Seal Power can be applied to a wide variety of substrates. Due to the fact
  that specific substrates such as plastics, like polycarbonates, etc may differ from
  manufacturer to manufacturer, we recommend a preliminary compatibility test.
•  Do not use as structural glazing sealant.
•  When applying make sure that the surface of the materials is not smudged with sealant.
•  A total absence of UV can cause a color change of the sealant.
• Dolphin Fix & Seal Power can discolour under extreme conditions or after very long UV
  exposure.
•  Do not use on natural stones like marbles, granite,….(staining)
• When using different reactive joint sealants, the first joint sealant must be completely
  hardened before that next one is applied.
•  Not suitable for bonding aquariums.
• Do not use in applications where continuous water immersion is possible
• Discolouration due to chemicals, high temperatures, UV-radiation may occur.
•  Contact with bitumen, tar or other plasticizer releasing materials such as EPDM,
  neoprene, butyl etc. is to be avoided since it can give rise to discoloration an loss of
  adhesion.

Liability

The content of the data sheet is the result of tests, monitoring and experience. It is general
in nature and does not constitute any liability. It is the responsibility of the user to
determine by his own tests whether the product is suitable for the application

Applications: