Dolphin – Fire Rated PU Foam

Dolphin – Fire Rated PU Foam

Dolphin B2 Fire Retardant (Flame Retardant) PU Foam is a premium quality Polyurethane Foam. It has excellent bonding strength, that adheres to the wide range of surfaces. Building insulation that can fill and enclose spares between roof tiles, concrete slabs, wall cavities, drilled holes, frame construction, gaps around windows and other substrates. It is a single component material; has moisture resistance and self-expanding properties.

It exerts a strong cohesive force on most material (Excluding gypsum, grease, and oily materials). Giving high performance of heat preservation and sound insulation without compromising the performance.

TDS   |    MSDS


Application Instructions:


  1. Shake Can vigorously for 45-60 seconds before and between uses
  2. To avoid wastage or clogged nozzle, utilize the product within 2 hours of opening the Can
  3. Make sure the application surface is free from dirt and grease. Also, Protect adjacent surface with tape and plastic film
  4. Remove the seal cap from the Can and put a clean spray nozzle
  5. Hold the cylinder upside down and dispense slowly. For a small gap, dispense PU Foam and fill the gap about 50%. Allow it to expand
  6. Apply multiple layers if needed. Sprinkle a small amount of water on the first layer and leave it for 10 minutes to be cured. Apply the second layer and repeat the process.
  7. Recommended single layer thickness is 5-8cm
  8. Wait for a minimum of 1 hour before performing the next step
  9. Use a knife to remove/trim excess foam
  10. If the layer thickness is more than 15cm; curing time is 12 hours
  11. PU Foam drops/Stains can be cleaned with paint thinner acetone or toluene
  12. For best result, apply it within defined temperature (From 5°C to 30°C)
  13. CFC and HCFC FREE

Safety Measures:


  1. Always keep the Can in an upright position
  2. Do not expose it to sunlight and temperature exceeding 50°C
  3. Do not pierce or burn Can even after uses
  4. Extremely flammable. No smoking during the application
  5. Use protective gloves, glasses and face protectant while applying

First AID Treatment:


Remove contaminated clothing and wash skin with soap and water. In case of contact with eyes, splash water into the eyes to remove the chemicals. Upon inhalation, leave the area to get fresh air. If swallowed, drink fluid in large quantity and consult the physician immediately.

FULLY CURED DOLPHIN PU FOAM IS NOT HARMFUL TO HEALTH

KEEP OUT OF REACH OF CHILDREN

WEAR GLOVES AND GOGGLES – CAN MAY BURST IF EXPOSED TO TEMPERATURE ABOVE 50 °C or IN DIRECT SUNLIGHT – DO NOT LEAVE IN AUTOMOBILE

Packaging:


Sr. NoVolumePackaging Type
1.750mlCan

Application Instructions:


  1. Shake Can vigorously for 45-60 seconds before and between uses
  2. To avoid wastage or clogged nozzle, utilize the product within 2 hours of opening the Can
  3. Make sure the application surface is free from dirt and grease. Also, Protect adjacent surface with tape and plastic film
  4. Remove the seal cap from the Can and put a clean spray nozzle
  5. Hold the cylinder upside down and dispense slowly. For a small gap, dispense PU Foam and fill the gap about 50%. Allow it to expand
  6. Apply multiple layers if needed. Sprinkle a small amount of water on the first layer and leave it for 10 minutes to be cured. Apply the second layer and repeat the process.
  7. Recommended single layer thickness is 5-8cm
  8. Wait for a minimum of 1 hour before performing the next step
  9. Use a knife to remove/trim excess foam
  10. If the layer thickness is more than 15cm; curing time is 12 hours
  11. PU Foam drops/Stains can be cleaned with paint thinner acetone or toluene
  12. For best result, apply it within defined temperature (From 5°C to 30°C)
  13. CFC and HCFC FREE

Safety Measures:


  1. Always keep the Can in an upright position
  2. Do not expose it to sunlight and temperature exceeding 50°C
  3. Do not pierce or burn Can even after uses
  4. Extremely flammable. No smoking during the application
  5. Use protective gloves, glasses and face protectant while applying

First AID Treatment:


Remove contaminated clothing and wash skin with soap and water. In case of contact with eyes, splash water into the eyes to remove the chemicals. Upon inhalation, leave the area to get fresh air. If swallowed, drink fluid in large quantity and consult the physician immediately.

FULLY CURED DOLPHIN PU FOAM IS NOT HARMFUL TO HEALTH

KEEP OUT OF REACH OF CHILDREN

WEAR GLOVES AND GOGGLES – CAN MAY BURST IF EXPOSED TO TEMPERATURE ABOVE 50 °C or IN DIRECT SUNLIGHT – DO NOT LEAVE IN AUTOMOBILE

Packaging:


Sr. NoVolumePackaging Type
1.750mlCan

Additional information
Industries Solution

Aluminum & Glass, Automotive, General Purpose, Hvac, Sanitary